Intelligent Sensors Knowledge Base
I noticed you have a 5 dry contact sensor for the sensorProbe2, do you have a wiring diagram of this and which color of wires represents which RJ-45 connection?
5 Dry Contact Sensor Pin-Out Diagram Yes, this is the wiring diagram for the 5 Dry Contact Sensor below.
I have a burglar alarm system that needs 12V and I want to control this with my sensorProbe8 and my dry RJ-45 dry contact sensor, how do I do that?
12V burglar alarm system on dry contacts sensorProbe8-X20? You can integrate the dry contact output from the unit to his burglar alarm system by using a 12V power supply and…
What is the best way I can trouble shoot a sensor if I think it is faulty?
How to trouble shoot AKCP sensor if suspected faulty? The simplest way to determine if you have a faulty sensor is to try connecting it to another RJ45 port on…
If I suspect I have a bad sensor, how long is the warranty and what should I do?
Unless you purchased and extended warranty, this period is one year after the purchase date. The RMA process begins with you contacting AKCPs Support Team at [email protected] who will determine…
Do I have to send my faulty sensor back to AKCP?
No, you do not have to ship the sensor back to us, however because of this, we do require that you send us proof that you have destroyed the faulty…
What if my sensor is not covered under my warranty plan any longer? Will AKCP offer me a discount if I want to purchase a replacement sensor?
Yes, AKCP offers a lifetime 50% discount off the current list price of the sensor, if you wish to purchase a replacement. We again require that you provide us with…
Can your 5 dry contact sensor for the sensorProbe2 be configured as inputs and outputs?
No, the 5 Dry Contact Sensor can only be configured as inputs. The regular single RJ-45 Intelligent Dry Contact Sensor can be configured as both an input and output.
Can your single dry contact RJ-45 sensor measure voltage, or how does it work? Why does it show in my web interface as a security sensor?
Our RJ-45 single Dry Contact Sensor is a switch type sensor, so it does not measure voltage, it is either on or off. You can configure this as either an…
Regarding your single dry contact RJ-45 sensor, when this is used as an output, the documentation says that Pin 2 (I/O) can source up to 20mA, so how much current can be taken from Pin 1 ? the 5V supply and how much current will Pin 2 sink?
We recommend 200mA of current can be taken from Pin 1 with the 5V supply. A: Pin 2 will sink 20mA of current.
Regarding your single dry contact RJ-45 sensor, can you please confirm the pin-out information for a dry contact that connects to one of the dry contact ports, also which pin supplies power (pin1, 5v,)?
Here is the pin-out for the dry contact sensor. The RJ-45 the combination is: White/orange, orange, white/green, blue, white/blue, green, white/brown, brown. On the sensor on the black wire: white/green…
Is it possible to connect my securitySensor up in series, if I wanted to monitor a number of doors in the same building for example? If so, how do I do that?
Yes, the securitySensor can actually be wired in sequence. You can take the contact from one security sensor and wire it to the next. The only limit to the number…
Is it possible to setup my RJ-45 dry contact sensor as a relay, If so, how do I do that?
Yes, You can use one of our RJ-45 dry contact sensors in the any of the 8 ports to drive a relay and a temperature sensor to trigger the output…
If I have a rely setup on my RJ-45 dry contact sensor is there a way to cycle this and If so, how do I do that?
You have two options for cycling the relay on the dry contact sensor. The first one is from the web interface as shown in the screen shot below. This shows…
I just finished a calibration process, but the reading is still a little bit off. Is there any way to fine tune the reading?
In the calibration process, we set the offset of the reference voltage so that the raw analog read 500 when the input to the RJ45 port is 1.25 volts. However,…
Do you have any sensor that is capable of reading the fluctuation of electricity, and send me reports?
How to monitor electricity fluctuations? We have a sensor that is capable of monitoring Voltage, Wattage and Amperage. This is our Power Meter Sensor. You can set alerts as with…
I noticed you have an airflow sensor, can you tell me how can I utilize this sensor in my environment to help prevent problems?
The AKCP airflow sensor is designed for systems that generate heat in the course of their operation and a steady flow of air is necessary to dissipate this heat generated….
Can you please explain how your airflow sensor works?
The way the air flow sensor works is there are two thermistors, one internal and one external. A thermistor changes resistance based on air temperature. The internal thermistor is the…
How accurate is your airflow sensor?
The airflow sensor is not a precision measuring instrument. This device is meant to measure the presence or the absence of air flow. The placement of the sensor is very…
Is it possible to extend the run length of my sensors?
Yes, you can extend the run length of your sensors, but each sensor has its own maximum, so please contact the AKCP Support Team about your specific sensor. Also remember…
I have one of you DC Voltmeter sensors and my question was can this sensor handle DC signals from 0 to 10 mV?
What is the resolution of the AKCP DC Voltmeter? The lowest signal will be 0.1V (100mV). We display only the one decimal place in the web interface of the unit….